8BVF0440H000.001-2 Mains EMC Line Filter

• Brand
  B&R
• Model
  8BVF0440H000.001-2
• Product Name
  ACOPOSmulti 45A Three-Phase Mains EMC Line Filter
• Place of Origin
  Austria
• HS Code
  8504500000
• Dimensions
  Width 135mm, Height 378mm, Depth 212mm
• Weight
  15kg
• Operating Temperature
  -25℃ ~ +55℃
• Storage Temperature
  -25℃ ~ +70℃
• Power Supply
  24VDC
• Warranty
  12 month
• Product Status
  New and original

Backed by abundant in-stock inventory and nearly 20 years of industry experience, our company stands as a leading player in the industrial control sector.We offer an extensive range of industrial control products covering numerous models. Should you have any other requirements, please feel free to contact us, and we will respond to you promptly.

Our main brand:

1.ABB's module cards, touch screens, controllers, etc., such as PP846 touch screen, IGCT starting with 5SHY, PM starting controller, AI, DO starting input/output module, SP starting Bailey module, etc

2.GE's module card CPUs, such as VMIC starter, IS200, IS215, IS400, IS420 series, etc,

3.Emerson's card components and EPRO probes, Westinghouse 1C series, Honeywell CC series, Schneider 140 series, Envision full series, Bentley 3500 series, Rexroth motors and drives, and Foxboro small modules.

Basic Overview

Model: 8BVF0440H000.001-2

Device Type: Three-phase EMC mains line filter

Matching Equipment: ACOPOSmulti power supply modules (8BVP0440HC00.000-1, 8BVP0440HW00.000-1)

Installation Form: Wall-mounted installation

Compliance Standard: EN 61800-3 Category C3 EMC standard

Input Parameters

Nominal Mains Voltage: 3×220 VAC ~ 3×480 VAC, voltage tolerance ±10%

Applicable Frequency: 50Hz / 60Hz, frequency tolerance ±4%

Applicable Power Grids: TN grid and TT grid systems

Rated Continuous Input Current: 45 Aeff

Short-Term Peak Input Current: 180 Aeff, maximum sustainable duration ≤10 seconds

Current Derating Requirements:

When ambient temperature exceeds 40℃, the rated current decreases by 0.4 Aeff for each 1℃ temperature rise;

When installation altitude exceeds 1000m, the overall rated current is reduced by 3.6 Aeff.

Input Terminals Definition: L1, L2, L3, PE protective earth terminal

Output Parameters

Output Terminals: L1', L2', L3', PE, designed for direct matching connection with ACOPOSmulti power units

Output Electrical Feature: Three-phase AC power after harmonic and electromagnetic interference filtering

Power Consumption: 210W power loss under full rated load

Applicable Wiring Specification: Conductors with cross-section ranging from 0.5 mm² to 16 mm²

Core Output Function: Effectively suppress conducted electromagnetic interference at the front end of servo drive equipment

Auxiliary I/O and Environmental Specifications

No digital signal or analog signal I/O ports, only power wiring terminals available.

Operating Ambient Temperature: -25℃ ~ +55℃

Internal Protection Configuration: Built-in surge suppression circuits and integrated EMI filtering components

1. Pre-operation Safety Preparation

Disconnect the three-phase main power and complete lockout-tagout, then fully release residual voltage.

Check the filter casing for deformation, scorching and foreign objects, and confirm matching 8BVP power module models.

Install the device vertically suspended or horizontally upward; flat horizontal installation is prohibited.

Ensure the ambient temperature stays between -25℃ and +55℃ with no heavy dust, oil mist or intense electromagnetic interference.

2. Wiring Procedures

Secure the M5 PE grounding bolt firmly to the cabinet ground busbar, which is required for all debugging scenarios.

Connect the three-phase mains to L1/L2/L3 input terminals with 0.5~16mm² ferruled wires and fasten terminals with specified torque.

Connect L1'/L2'/L3'/PE output terminals to the front of matched 8BVP power modules.

Separate power cables from signal cables and avoid squeezing or sharp bending near heat dissipation zones.

Use a multimeter to inspect open circuits, short circuits and phase errors before power-on.

3. Power-on Commissioning

Apply power gradually and verify input voltage within 3×220~480VAC (±10% tolerance).

Measure output voltage to guarantee three-phase balance and stable voltage.

Energize rear power supplies and servo drives to observe startup conditions.

Run under no load for 30 minutes and check for overheating and abnormal noise.

Switch to rated load, monitor real-time current and execute current derating above 40℃ ambient temperature or 1000m altitude.

4. Daily Inspection During Operation

Check loose terminals, aging cables and casing overheating regularly.

Test input and output voltage & current to maintain values within rated ranges.

Keep ventilation clear; do not place objects on the filter surface.

No disassembly or internal wiring changes while powered on.

5. Shutdown Operation

Normal shutdown: halt servo systems first, then cut off main input power.

Emergency shutdown: turn off the upstream circuit breaker and record fault details.

Long-term shutdown: cut power, clean dust and maintain dry cabinet environment.

6. Troubleshooting & Maintenance

Overheating: check load current, temperature and blocked heat dissipation, then adjust derating current.

Noise & vibration: check loose terminals, loose mounting and unstable grid voltage.

Severe interference: recheck grounding, shielding cables and installation spacing.

Internal damage: stop operation immediately; no on-site disassembly, send back for official maintenance.

7. Operation Prohibitions

Reverse connection of input and output terminals is forbidden.

High voltage withstand test on the filter is forbidden.

Long-term overload beyond rated current and temperature range is forbidden.

Live wiring and disassembly of the casing are forbidden.

Frequently Asked Questions (FAQ)

1.How fast will you reply to my inquiry?

We process all inquiries efficiently and will respond promptly once we receive your message.

2.Do you carry large inventory of industrial control parts?

We maintain massive ready stock of mainstream automation spare parts to shorten lead times.

3.Can you source discontinued or obsolete PLC & DCS modules?

Absolutely.
We specialize in sourcing hard-to-find, obsolete and out-of-production industrial control components.

4.Do you inspect goods before shipment?

Every product undergoes thorough inspection before packing and dispatch.

5.Can you ship orders worldwide?

We provide global shipping with flexible logistics for urgent and regular orders.

6.What payment methods are available?

We accept multiple secure payment options. Please contact our sales team for detailed terms.