DS200TCDAG1BDB GE Input and Output Circuit Board

• Brand
  GE
• Model
  DS200TCDAG1BDB
• Product Name
  Mark V Speedtronic Digital Input & Output Processing Circuit Board
• Place of Origin
  United States
• HS Code
  8542319000
• Dimensions
  168mm × 152mm × 56mm
• Weight
  0.95kg
• Operating Temperature
  -40°C ~ +70°C
• Storage Temperature
  -55°C ~ +105°C
• Power Supply
  24VDC
• Warranty
  12 month
• Product Status
  New and original

Backed by abundant in-stock inventory and nearly 20 years of industry experience, our company stands as a leading player in the industrial control sector.We offer an extensive range of industrial control products covering numerous models. Should you have any other requirements, please feel free to contact us, and we will respond to you promptly.

Our main brand:

1.ABB's module cards, touch screens, controllers, etc., such as PP846 touch screen, IGCT starting with 5SHY, PM starting controller, AI, DO starting input/output module, SP starting Bailey module, etc

2.GE's module card CPUs, such as VMIC starter, IS200, IS215, IS400, IS420 series, etc,

3.Emerson's card components and EPRO probes, Westinghouse 1C series, Honeywell CC series, Schneider 140 series, Envision full series, Bentley 3500 series, Rexroth motors and drives, and Foxboro small modules.

Pre-power Static Inspection

Install the board into the specified Mark V rack slot and inspect the PCB for damage and loose components.

Configure onboard jumpers as required while keeping factory test jumpers intact.

Check cables and wiring for tight connections, test power insulation to avoid short circuits, and ensure cabinet single-point grounding with resistance ≤4Ω.

Power-on Initial Self-check

Power on the rack slowly; steady green LEDs indicate normal initialization, while flashing red LEDs represent hardware faults.

Measure backplane voltages (+5V, ±15VDC, 24VDC) with a multimeter.

Access the Mark V HMI to confirm normal Q-Bus communication without alarms.

Communication Debugging

Check real-time data exchange between the board and R/S/T triple-redundant main boards via Q-Bus.

Connect a maintenance device to the RS232 port to check PROM parameters and offline programs.

Ensure smooth, delay-free data transmission with peripheral signal boards.

I/O Channel Calibration & Functional Test

Test digital inputs by simulating 24VDC signals to align HMI feedback; manually trigger relay outputs to check contact performance.

Complete zero and span calibration for 4–20mA and voltage analog channels.

Manually trigger protective conditions to test interlock and trip response speed.

System Joint Debugging

Connect the board to sensors, actuators and the ETS system, and simulate startup, load regulation and load shedding.

Monitor signal stability and anti-interference ability, and adjust parameters to resolve logic conflicts.

Stable Operation Inspection & Acceptance

Carry out a 72-hour no-load test with regular status records; repeatedly simulate typical faults to verify protection reliability.

Clear temporary faults, archive commissioning records and complete acceptance.

Post-commissioning Check

Secure all connectors and organize wiring; file jumper settings and calibration records for future maintenance.

Input

Digital discrete input: 24VDC sinking signal compatible with passive dry contacts, collecting interlock and position switch status.

Analog input: 4–20mA current and ±10V voltage signals for pressure, temperature and vibration sensor acquisition.

LVDT differential AC input: low-amplitude signals for valve position detection.

Backplane input: +5VDC, ±15VDC logic power and Q-Bus communication signals.

Output

Analog output: configurable 4–20mA and ±10V control signals for valves and servo actuators.

Relay output: isolated normally-open dry contacts rated at 240VAC/5A for alarms and safety interlock trips.

Bus output: processed digital data transmitted to R/S/T triple-redundant main boards via Q-Bus.

LVDT excitation output: stable AC power supply for displacement sensors.

Frequently Asked Questions (FAQ)

1.How fast will you reply to my inquiry?

We process all inquiries efficiently and will respond promptly once we receive your message.

2.Do you carry large inventory of industrial control parts?

We maintain massive ready stock of mainstream automation spare parts to shorten lead times.

3.Can you source discontinued or obsolete PLC & DCS modules?

Absolutely.
We specialize in sourcing hard-to-find, obsolete and out-of-production industrial control components.

4.Do you inspect goods before shipment?

Every product undergoes thorough inspection before packing and dispatch.

5.Can you ship orders worldwide?

We provide global shipping with flexible logistics for urgent and regular orders.

6.What payment methods are available?

We accept multiple secure payment options. Please contact our sales team for detailed terms.